基于特征贡献率的机械故障分类方法

为了使7075铝合金薄壁件表面喷丸加工应力得到松弛和均化，运用ANSYS建立平台式振动时效有限元模型，通过振动模态和谐响应分析，获得最佳激振频率和试样装夹位置。在此基础上，将薄壁框架件置于平台上进行振动时效处理，以验证仿真分析结果，评价其对试样表面应力作用效果。结果表明：在亚共振频率为112 Hz时，试样在平台零振幅和最大弯曲位置处分别对称布置，时效后表面均形成应力松弛，松弛率分别为29.5%和33.3%，不均匀波动分别为20.3%和20.7%，而沿振动方向松弛程度不均匀，说明激振力造成了材料表面组织屈服，且屈服程度与应力强度有关。提出再时效-位置交叠方法，使应力松弛不均匀度分别下降到9.9%和15.9%，应力均化得到改善，该研究工作为薄壁类零件表面应力均匀化提供了参考。     

Highly Stretchable and Sensitive SBS/Graphene Composite Fiber for Strain Sensors

Flexible strain sensors have attracted tremendous interests due to the emergence of intelligent wearable technology. Electrically conductive fibers are desirable candidates for flexible strain sensors, but up til now, there still exist enormous challenges to obtain conductive fibers exhibiting simultaneously high stretchability and high strain sensitivity. This paper introduces a poly (styrene‐butadiene‐styrene) (SBS)/graphene (Gr) composite fiber‐based flexible strain sensor fabricated by a facile and highly scalable wet spinning method. The results demonstrate that the graphene content has significant influence on the morphology, mechanical properties, and electromechanical properties of the composite fibers. The fibers with 5 wt% graphene have a wide response range of up to 100% strain, a high electrical sensitivity with the gauge factor of 10083.98 at 100% strain, and meanwhile, a high level of stability for 2100 stretching–releasing cycles under an applied strain of 20%. Furthermore, the SBS‐5%Gr composite fibers display excellent sensing performance in detecting human upper limb movements at different joints including hand joints, wrist joints, elbow joints, and shoulder joints.     

球化退火工艺对高碳马氏体不锈钢8Cr13MoV组织及性能的影响

为了优化高碳马氏体不锈钢8Cr13MoV的球化热处理工艺,提高其退火后的冷加工性能,采用微观组织分析法以及拉伸力学分析法研究了球化退火过程中奥氏体化保温时间和冷却速率对8Cr13MoV钢的球化效果影响。结果表明, 随着奥氏体保温时间的增加,组织中细颗粒状碳化物数量减少,索氏体数量增多,试样硬度先降低后升高,但断后伸长率持续增加;随冷却速率增加,试样组织中细颗粒状碳化物和索氏体数量、硬度和强度增加,断后伸长率降低。综合对比,奥氏体保温时间ϕ90 min时试样综合力学性能较好,冷却速率应控制在25 ℃·h^-1以内。与奥氏体保温时间相比,冷却速率对力学性能的影响更加显著。     

Effect of Biochar as Reductant on Magnetizing-roasting Behavior of Pyrite Cinder

The effect of biochar substituted for anthracite as reductant on magnetizing-roasting pyrite cinder was investigated.The key of magnetizing-roasting is the gasification reaction between reductants and CO2.Since biochar could react with CO2 more rapidly at lower temperature,the reactivity of biochar is better than that of anthracite.The gasification of biochar could produce reducing condition ofφCO/(φCO+φCO2)about 10%-20% between 700-800 ℃,which is in accord with the atmosphere and temperature of Fe2O3 reduction.So it is beneficial to the reduction of iron mineral of pyrite cinder.Compared with anthracite,biochar could decrease the roasting temperature from825 to 750 ℃ and roasting time from 20 to 15min,which shows that a better effect of magnetization could be obtained in the condition of lower temperature and shorter time.Using biochar as reductant,iron concentrate extracted from pyrite cinder as about 64%iron grade could be produced,and the recovery is over 90% under the condition of above 90% grinding particle less than 0.045 mm and magnetic intensity of 0.124-0.194 T.     

Application of Vis–NIR hyperspectral imaging in classification between fresh and frozen-thawed pork Longissimus Dorsi muscles

Fresh and frozen-thawed (F-T) pork meats were classified by Vis–NIR hyperspectral imaging. Eight optimal wavelengths (624, 673, 460, 588, 583, 448, 552 and 609 nm) were selected by successive projections algorithm (SPA). The first three principal components (PCs) obtained by principal component analysis (PCA) accounted for over 99.98% of variance. Gray-level-gradient co-occurrence matrix (GLGCM) was applied to extract 45 textural features from the PC images. The correct classification rate (CCR) was employed to evaluate the performance of the partial least squares-discriminate analysis (PLS-DA) models, by using (A) the reflected spectra at full wavelengths and (B) those at the optimal wavelengths, (C) the extracted textures based on the PC images, and (D) the fused variables combining spectra at the optimal wavelengths and textures. The results showed that the best CCR of 97.73% was achieved by applying (D), confirming the high potential of textures for fresh and F-T meat discrimination.     

The impact of inoculum source,inoculum to substrate ratio and sample preservation on methane potential from different substrates

Batch experiments were conducted to evaluate the impact of inoculum sources, inoculum to substrate (IS) ratio and storage conditions on the potential and production rate of methane (CH₄) from different substrates: wheat straw, whole crop maize, cattle manure, grass and cellulose.The results of the test with four inocula and four substrates indicated that inoculum source could have a significant impact on both CH₄ potential (BMP) and the kinetics parameters of different substrates. The two inocula showing the highest BMP and production rates in each period were those coming from a feeding with more than 70% of animal manure under thermophilic conditions. The impact of the IS ratio in the range 0.25–2.5, in terms of g volatile solids (VS) substrate/g VS inoculum, depended on substrate type. Maize silage was more affected to changes in the IS ratio than wheat straw. The optimal IS ratio range for maize was 1.0–1.5, however, a wider IS range can be used in wheat straw (0.5–2.5). The impact of freezing and drying depended on biomass type. Freezing, drying and ensiling of grass increased the CH₄ yield compared to fresh grass. Drying of maize had no impact while freezing reduced the CH₄ potential. Drying and freezing had no impact on straw.     

Assessment of local strain field in adhesive layer of an unsymmetrically repaired CFRP panel using digital image correlation

The present study focuses on experimental investigation of through the thickness displacement and strain field in thin adhesive layer in single sided (unsymmetrical) patch repaired CFRP (carbon fiber reinforced polymer) panel under tensile load. Digital image correlation (DIC) technique is employed to acquire the displacement and strain (longitudinal, peel and shear) field. Experimental determination of shear transfer length based on shear strain field obtained from DIC is introduced to estimate the optimum overlap length which is an essential parameter in patch design for the repair of CFRP structures. Further, DIC experiment with magnified optics is performed to get an insight into complex and localized strain field over thin adhesive layer especially at critical zones leading to damage initiation. The failure mechanism, load displacement behavior, damage initiation and propagation are closely monitored using DIC. The influence of patch edge tapering on strain distribution in adhesive layer is also investigated. The DIC successfully captures the global and localized strain field at critical zones over thin adhesive layer and further helps in monitoring the damage based on strain anomalies. Strains are found to have maximum magnitude at the patch overlap edge and the shear strain level in adhesive layer is higher than the peel strain. Normal tapering increases the peel strain and has negligible influence on shear strain level in adhesive layer. The recommended overlap length is found to be consistent with the recommendation in the literature. Whole field strain pattern and the overlap length obtained from experiment are further compared with the finite element analysis results and they appear to be in good coherence.     

Decay Rate Kinetics of Ozone Gas in Rice Grains

The present study was carried out to evaluate the effects of ozone on rice grains for the following three conditions: saturation time, decay rate, and half-life of ozone. Experiments were performed in different bed thicknesses (5 and 10 cm) and moisture content (11.4 and 14.2% wb) at atmospheric conditions. The lowest saturation time of ozone was 119 min, with the concentration of 516 ppm for rice grains ozonated at 5-cm bed thickness with 11.4% (wb) moisture content. The decay rate kinetics of ozone obtained were consistent with a first-order model. Regarding the half-life of ozone, the lowest value obtained was 6.78 min for rice grains ozonated at 10-cm bed thickness with 14.2% (wb) moisture content.     

Effect of Solute Elements and Cooling Rate on Strain in Brittle Temperature Range of Continuously Cast Strand

A micro-segregation model of solute elements in mushy zone withδ/γtransformation during solidification was established based on the regular hexagon transverse cross section of dendrite shape proposed by finite difference method under the non-equilibrium solidification condition.The model was used to calculate the non-equilibrium pseudo binary Fe-C phase diagram and the strain of steels induced by variation of temperature in brittle temperature range.On the basis of the phase diagram and the strain,the strain curve in brittle temperature range as a function of carbon content for continuously cast strand was introduced and obtained.Solute elements change the position of the strain curve.And cooling rate changes the position and the shape of the strain curve.The comprehensive formula of the strain as functions of solute elements and cooling rate in brittle temperature range has been obtained by nonlinear fitting program.     

大型球磨机订购（制造）设计联络中零部件结构优化的探讨

针对大型球磨机使用中存在的问题，对球磨机主要零部件结构缺陷进行分析并提出解决方案。通过设计联络，提前对球磨机主要零部件结构进行优化，消除设备缺陷。大型球磨机设计联络中对主要零部件结构进行优化，对提高球磨机的运转率有着事半功倍的作用。